Câu hỏi

26/05/2013 10:43
Máy báo lỗi 200.20 là lỗi gì ah?
Máy bắt đầu in thì báo lỗi 200.20 Paper Jam Remove Cartridge , sau khi lấy giấy kẹt ra và enter thì in được , và lập lại từ đầu in lại thì lại báo lỗi và cứ lập đi lập lại luôn , xin cho biết máy bị lỗ gì ? Máy X342N mua ngày 18/5/2007 tại 211-213 Võ Văn Tần Q.3 TP.HCM
TungNo1
26/05/2013 10:43
taimuoi
26/05/2013 10:43
Danh sách câu trả lời (2)

Tạm dịch theo google thế này nhé
Lỗi: "200 Giấy Jam - Cartridge Hủy bỏ"
Lỗi: "200 kẹt giấy - lấy ra khỏi Cartridge"
Nếu không có giấy kẹt trong máy in và bạn vẫn nhận được lỗi này mỗi khi bạn bật máy in trên, có cái gì có thể ngăn chặn các cảm biến. Tắt máy in kiểm tra lại đường dẫn giấy, đặc biệt là ở phía trên của máy in, máy có thể lộ một mảnh giấy, máy in hỏng một phần, vv
Để loại bỏ các giấy tờ kẹt:
- Mở cửa phía trên cửa trước.
- Nắm khe cartridge bởi tay nắm, kéo nó về phía với bạn và hơi nâng lên để nó ra khỏi phải giữ.
- Sau đó kéo các cartridge thẳng ra đối với bạn.
(Xem hình.)
Vị trí của các nguồn cấp dữ liệu lăn đòn bẩy ra và nhẹ nhàng đẩy nó lại để các áp lực trên giấy. (Xem hình .)
Lấy giấy ra.
LƯU Ý! Giấy tờ có thể được gắn với Trống, có thể dơ quần áo.
Nếu bạn thấy không có giấy jammed dưới cartridge, loại bỏ giấy khay 1. Các giấy tờ có thể không có fed tất cả các cách vào máy in.
Cài đặt lại các khay giấy và Mực máy in Laser.
Gần phía trên cửa trước.
Nếu nhận được giấy là hư hỏng khi nó bị kẹt tại cảm biến hoặc theo cartridge, bạn có thể có khả năng pinpoint vấn đề với một đóng nhìn, nơi đầu cạnh đã được ngừng.
Kiểm tra cho bất cứ khía cạnh đầu của tờ giấy.
Nếu nó là hư hỏng, kiểm tra đường dẫn giấy cho bất kỳ obstructions.
Bạn cũng có thể thử một Mực máy in Laser nếu bạn có một trong số chứng khoán. Các giấy tờ có thể bị kẹt trên cartridge.
Nếu bạn không thể tìm thấy bất kỳ obstruction, máy in sẽ cần có dịch vụ cho các vấn đề isolate và thay thế các thành phần không.
If you receive this 200 Paper Jam error message on power up and there is no paper jammed in the printer, the printer's input sensor flag may be stuck. Nếu bạn nhận được 200 Giấy Jam này thông báo lỗi về quyền lực lên và không có giấy jammed trong máy in, máy in các cảm biến đầu vào của cờ có thể bị khó khăn.
Look for the green bellcrank release lever at the left side of the inside of the printer, under where the cartridge goes. You will also see two white rollers and, underneath them, two white gears. Tìm bellcrank xanh "đòn bẩy" phát hành ở phía bên trái của các bên trong của máy in, máy dưới nơi cartridge đi. Bạn cũng sẽ thấy hai màu trắng và Rollers, bên dưới họ, hai bánh răng trắng. Just back and to the right of the back gear, you should see a black, plastic flag sticking up through a hole in the black plastic floor of the printer. Chỉ cần quay lại và vào bên phải của gear trở lại, bạn sẽ thấy một đen, cờ nhựa dính lên thông qua một lỗ trong sàn nhựa màu đen của các máy in. This flag is the input sensor flag. Cờ này là cảm biến đầu vào cờ.
Using a pen or pencil, push the flag towards the back of the printer. Bằng cách sử dụng một bút hay bút chì, đẩy cờ theo hướng phía sau của máy in. It should lie down. Nó nên nằm xuống. When you remove the pen or pencil, the flag should pop back up freely. Khi bạn loại bỏ các bút hay bút chì, cờ nên bật lên lại tự do.
If it does not, see if you can find out why. Nếu không, xem nếu bạn có thể tìm hiểu lý do tại sao. There may be a piece of paper or broken printer part in the way or the flag may have come loose. Có thể có một mảnh giấy hoặc máy in hỏng một phần trong bằng cách này hay cách cờ có thể có đến loose.
If the input sensor flag is damaged or missing, you will probably need service on your printer. Nếu các cảm biến đầu vào cờ đã bị hư hoặc thiếu, bạn sẽ cần có dịch vụ của bạn trên máy in.
Lỗi: "200 Giấy Jam - Cartridge Hủy bỏ"
Lỗi: "200 kẹt giấy - lấy ra khỏi Cartridge"
Nếu không có giấy kẹt trong máy in và bạn vẫn nhận được lỗi này mỗi khi bạn bật máy in trên, có cái gì có thể ngăn chặn các cảm biến. Tắt máy in kiểm tra lại đường dẫn giấy, đặc biệt là ở phía trên của máy in, máy có thể lộ một mảnh giấy, máy in hỏng một phần, vv
Để loại bỏ các giấy tờ kẹt:
- Mở cửa phía trên cửa trước.
- Nắm khe cartridge bởi tay nắm, kéo nó về phía với bạn và hơi nâng lên để nó ra khỏi phải giữ.
- Sau đó kéo các cartridge thẳng ra đối với bạn.
(Xem hình.)
Vị trí của các nguồn cấp dữ liệu lăn đòn bẩy ra và nhẹ nhàng đẩy nó lại để các áp lực trên giấy. (Xem hình .)
Lấy giấy ra.
LƯU Ý! Giấy tờ có thể được gắn với Trống, có thể dơ quần áo.
Nếu bạn thấy không có giấy jammed dưới cartridge, loại bỏ giấy khay 1. Các giấy tờ có thể không có fed tất cả các cách vào máy in.
Cài đặt lại các khay giấy và Mực máy in Laser.
Gần phía trên cửa trước.
Nếu nhận được giấy là hư hỏng khi nó bị kẹt tại cảm biến hoặc theo cartridge, bạn có thể có khả năng pinpoint vấn đề với một đóng nhìn, nơi đầu cạnh đã được ngừng.
Kiểm tra cho bất cứ khía cạnh đầu của tờ giấy.
Nếu nó là hư hỏng, kiểm tra đường dẫn giấy cho bất kỳ obstructions.
Bạn cũng có thể thử một Mực máy in Laser nếu bạn có một trong số chứng khoán. Các giấy tờ có thể bị kẹt trên cartridge.
Nếu bạn không thể tìm thấy bất kỳ obstruction, máy in sẽ cần có dịch vụ cho các vấn đề isolate và thay thế các thành phần không.
If you receive this 200 Paper Jam error message on power up and there is no paper jammed in the printer, the printer's input sensor flag may be stuck. Nếu bạn nhận được 200 Giấy Jam này thông báo lỗi về quyền lực lên và không có giấy jammed trong máy in, máy in các cảm biến đầu vào của cờ có thể bị khó khăn.
Look for the green bellcrank release lever at the left side of the inside of the printer, under where the cartridge goes. You will also see two white rollers and, underneath them, two white gears. Tìm bellcrank xanh "đòn bẩy" phát hành ở phía bên trái của các bên trong của máy in, máy dưới nơi cartridge đi. Bạn cũng sẽ thấy hai màu trắng và Rollers, bên dưới họ, hai bánh răng trắng. Just back and to the right of the back gear, you should see a black, plastic flag sticking up through a hole in the black plastic floor of the printer. Chỉ cần quay lại và vào bên phải của gear trở lại, bạn sẽ thấy một đen, cờ nhựa dính lên thông qua một lỗ trong sàn nhựa màu đen của các máy in. This flag is the input sensor flag. Cờ này là cảm biến đầu vào cờ.
Using a pen or pencil, push the flag towards the back of the printer. Bằng cách sử dụng một bút hay bút chì, đẩy cờ theo hướng phía sau của máy in. It should lie down. Nó nên nằm xuống. When you remove the pen or pencil, the flag should pop back up freely. Khi bạn loại bỏ các bút hay bút chì, cờ nên bật lên lại tự do.
If it does not, see if you can find out why. Nếu không, xem nếu bạn có thể tìm hiểu lý do tại sao. There may be a piece of paper or broken printer part in the way or the flag may have come loose. Có thể có một mảnh giấy hoặc máy in hỏng một phần trong bằng cách này hay cách cờ có thể có đến loose.
If the input sensor flag is damaged or missing, you will probably need service on your printer. Nếu các cảm biến đầu vào cờ đã bị hư hoặc thiếu, bạn sẽ cần có dịch vụ của bạn trên máy in.

MỘT SỐ THÔNG BÁO LỖI CỦA HỌ MÁY IN HP-LASERJET
+ 02 Warning Up: Nếu thông báo này kéo dài, có thể cáp giao tiếp hoặc mối nối kết giao tiếp có vấn đề, kiểm tra lại cáp máy in, cổng LPT và có thể cả mạch điện giao tiếp của máy in.
+ 05 Self -Test: Một cuộc tự kiểm tra của máy in đang diễn ra, nếu thông báo này kéo dài, có thể mạch điện bên trong đang trục trặc.
+ 11 Paper Out: Không có giấy trong khay hoặc khay giấy gắn không chính xác vào máy
+ 12 Printer Open: Chưa đóng nắp đậy máy in hoặc hộp mực lắp không đúng cách
+ 12 Printer Open or No EP: Chưa dậy nắp máy in hoặc hộp mực EP có vấn đề (bị thiếu, bị vỡ...) cũng có thể quạt giải nhiệt không làm việc
+ 13 Paper Jam: Kẹt giấy trong máy in
+ 14 No EP Cart: không có hộp mực/EP trong máy hoặc hộp mực hỏng
+ 14 No Toner Cart: Giống như trên
+ 16 Toner Low: Gần hết bột mực hoặc hộp mực không tiếp xúc tốt với mạch điện trong máy in
+ 18 Aux I/O Init (Nt Rdy): Kiểm tra lại Card I/O
+ 20 Mem Overflow: Lỗi tràn bộ nhớ do quá nhiều dữ liệu gởi đến máy in ...
Sửa lỗi của bạn như sau Error: " 200 Paper Jam - Remove Cartridge"
If there is no paper jammed in the printer and you still receive this error every time you turn the printer on, there could be something blocking the sensor. A close examination of the paper path, especially at the front of the printer, might reveal a piece of paper, a broken printer part, etc.
To remove the jammed sheet of paper :
Open the upper front door.
Grasping the print cartridge by the hand grip, pull it towards you and slightly up to lift it out of the holder.
Then pull the cartridge straight out towards you. (See picture below.)
http://www.laserquipt.com/support/styles/lq/images/200.jpg
Locate the feed roller release lever and gently push it back to release the pressure on the paper. (See picture below.)
http://www.laserquipt.com/support/styles/lq/images/201.jpg
Pull the paper out.
CAUTION! The paper may be covered with unfused toner, which can stain garments.
If you see no paper jammed under the cartridge, remove paper tray 1. The paper may not have fed all of the way into the printer.
Reinstall the paper tray and the toner cartridge.
Close the upper front door.
If paper is getting damaged when it is jammed at the sensor or under the cartridge, you may be able to pinpoint the problem with a close look at where the leading edge was stopped.
Check for any damage to the leading edge of the paper.
If it is damaged, check the paper path for any obstructions.
You can also try another toner cartridge if you have one in stock. The paper may be catching on the edge of the cartridge.
If you are not able to find any obstruction, the printer will probably need service to isolate the problem and replace the failing component.
If you receive this 200 Paper Jam error message on power up and there is no paper jammed in the printer, the printer's input sensor flag may be stuck.
Look for the green bellcrank release lever at the left side of the inside of the printer, under where the cartridge goes. You will also see two white rollers and, underneath them, two white gears. Just back and to the right of the back gear, you should see a black, plastic flag sticking up through a hole in the black plastic floor of the printer. This flag is the input sensor flag.
Using a pen or pencil, push the flag towards the back of the printer. It should lie down. When you remove the pen or pencil, the flag should pop back up freely.
If it does not, see if you can find out why. There may be a piece of paper or broken printer part in the way or the flag may have come loose.
If the input sensor flag is damaged or missing, you will probably need service on your printer.
+ 02 Warning Up: Nếu thông báo này kéo dài, có thể cáp giao tiếp hoặc mối nối kết giao tiếp có vấn đề, kiểm tra lại cáp máy in, cổng LPT và có thể cả mạch điện giao tiếp của máy in.
+ 05 Self -Test: Một cuộc tự kiểm tra của máy in đang diễn ra, nếu thông báo này kéo dài, có thể mạch điện bên trong đang trục trặc.
+ 11 Paper Out: Không có giấy trong khay hoặc khay giấy gắn không chính xác vào máy
+ 12 Printer Open: Chưa đóng nắp đậy máy in hoặc hộp mực lắp không đúng cách
+ 12 Printer Open or No EP: Chưa dậy nắp máy in hoặc hộp mực EP có vấn đề (bị thiếu, bị vỡ...) cũng có thể quạt giải nhiệt không làm việc
+ 13 Paper Jam: Kẹt giấy trong máy in
+ 14 No EP Cart: không có hộp mực/EP trong máy hoặc hộp mực hỏng
+ 14 No Toner Cart: Giống như trên
+ 16 Toner Low: Gần hết bột mực hoặc hộp mực không tiếp xúc tốt với mạch điện trong máy in
+ 18 Aux I/O Init (Nt Rdy): Kiểm tra lại Card I/O
+ 20 Mem Overflow: Lỗi tràn bộ nhớ do quá nhiều dữ liệu gởi đến máy in ...
Sửa lỗi của bạn như sau Error: " 200 Paper Jam - Remove Cartridge"
If there is no paper jammed in the printer and you still receive this error every time you turn the printer on, there could be something blocking the sensor. A close examination of the paper path, especially at the front of the printer, might reveal a piece of paper, a broken printer part, etc.
To remove the jammed sheet of paper :
Open the upper front door.
Grasping the print cartridge by the hand grip, pull it towards you and slightly up to lift it out of the holder.
Then pull the cartridge straight out towards you. (See picture below.)
http://www.laserquipt.com/support/styles/lq/images/200.jpg
Locate the feed roller release lever and gently push it back to release the pressure on the paper. (See picture below.)
http://www.laserquipt.com/support/styles/lq/images/201.jpg
Pull the paper out.
CAUTION! The paper may be covered with unfused toner, which can stain garments.
If you see no paper jammed under the cartridge, remove paper tray 1. The paper may not have fed all of the way into the printer.
Reinstall the paper tray and the toner cartridge.
Close the upper front door.
If paper is getting damaged when it is jammed at the sensor or under the cartridge, you may be able to pinpoint the problem with a close look at where the leading edge was stopped.
Check for any damage to the leading edge of the paper.
If it is damaged, check the paper path for any obstructions.
You can also try another toner cartridge if you have one in stock. The paper may be catching on the edge of the cartridge.
If you are not able to find any obstruction, the printer will probably need service to isolate the problem and replace the failing component.
If you receive this 200 Paper Jam error message on power up and there is no paper jammed in the printer, the printer's input sensor flag may be stuck.
Look for the green bellcrank release lever at the left side of the inside of the printer, under where the cartridge goes. You will also see two white rollers and, underneath them, two white gears. Just back and to the right of the back gear, you should see a black, plastic flag sticking up through a hole in the black plastic floor of the printer. This flag is the input sensor flag.
Using a pen or pencil, push the flag towards the back of the printer. It should lie down. When you remove the pen or pencil, the flag should pop back up freely.
If it does not, see if you can find out why. There may be a piece of paper or broken printer part in the way or the flag may have come loose.
If the input sensor flag is damaged or missing, you will probably need service on your printer.
Trả lời câu hỏi
Câu hỏi lĩnh vực Phần cứng
Rao vặt Siêu Vip